小乔 发表于 2023-1-30 09:24:25

CCNA LAB 100: Configuring GRE Point-To-Point Tunnels

本帖最后由 小乔 于 2023-1-30 09:28 编辑


Lab Objective
The objective of this lab exercise is for you to learn how to configure point-to-point GRE tunnels.


Lab Purpose:
Generic Routing Encapsulation (GRE) is IP protocol number 47; its main purpose is to encapsulate any network layer protocol. As a Cisco engineer, as well as in the Cisco CCNA exam, you will be expected to know how to implement GRE tunnels.

Certification Level:
This lab is suitable for ICND2 and CCNA certification exam preparation.

Lab Difficulty:
This lab has a difficulty rating of 7/10.

Readiness Assessment:
When you are ready for your certification exam, you should complete this lab in no more than 20 minutes.


Lab Topology:
Please use the following topology to complete this lab exercise:




Task 1:
Configure hostnames on R1 and R2 as illustrated in the topology (R1 is on the left).

Task 2:
Configure each router with its respective IPv4 addresses on both of their FastEthernet interfaces.

Task 3:
Configure a GRE tunnel (numbered 1) on each router with the respective IPv4 address (10.10.10.0/30) as per the diagram and add the following settings:


Tunnel source is interface f0/0;
Tunnel destination is the other router’s interface f0/0; and
Set the tunnel mode to GRE.
Task 4:
Configure a static route on R1 to 192.168.2.0/24 via the Tunnel 1 interface, and configure a static route on R2 to 192.168.1.0/24 via the Tunnel 1 interface.

Task5:
Check the status of the interface tunnel and make sure that traffic is flowing through the tunnel as expected.

Configuration and Verification
Task 1:
For reference information on configuring hostnames, please refer to earlier labs.

Task 2:
For reference information on configuring IP addressing, please refer to earlier labs.


Task 3:
R1#config t
Enter configuration commands, one per line.End with CTRL/Z.
R1(config)#int Tunnel 1
R1(config-if)#ip address 10.10.10.1 255.255.255.252
R1(config-if)#tunnel source f0/0
R1(config-if)#tunnel destination 172.16.1.2
R1(config-if)#tunnel mode gre ip

R2(config)#int Tunnel 1
R2(config-if)#ip address 10.10.10.2 255.255.255.252
R2(config-if)#tunnel source f0/0
R2(config-if)#tunnel destination 172.16.1.1
R2(config-if)#tunnel mode gre ip
Task 4:
R1(config)#ip route 192.168.2.0 255.255.255.0 tunnel 1

R2(config)#ip route 192.168.1.0 255.255.255.0 tunnel 1
Task 5:
R1#sh ip interface brief
Interface      IP-Address      OK? Method Status       Protocol
FastEthernet0/0172.16.1.1      YES manual up         up
FastEthernet0/1192.168.1.1   YES manual up         up      
Tunnel1          10.10.10.1      YES manual up         up      

R2#sh ip int brief
Interface          IP-Address      OK? Method Status   Protocol
FastEthernet0/0    172.16.1.2      YES manual up         up      
FastEthernet0/1    192.168.2.1   YES manual up         up      
Tunnel1            10.10.10.2      YES manual up         up

R1#show interface tunnel 1
Tunnel1 is up, line protocol is up
Hardware is Tunnel
Internet address is 10.10.10.1/30
MTU 1514 bytes, BW 9 Kbit/sec, DLY 500000 usec, reliability 255/255, txload 1/255, rxload 1/255
Encapsulation TUNNEL, loopback not set
Keepalive not set
Tunnel source 172.16.1.1 (FastEthernet0/0), destination 172.16.1.2
Tunnel protocol/transport GRE/IP

R2#show interface tunnel 1
Tunnel1 is up, line protocol is up
Hardware is Tunnel
Internet address is 10.10.10.2/30
MTU 1514 bytes, BW 9 Kbit/sec, DLY 500000 usec, reliability 255/255, txload 1/255, rxload 1/255
Encapsulation TUNNEL, loopback not set
Keepalive not set
Tunnel source 172.16.1.2 (FastEthernet0/0), destination 172.16.1.1
Tunnel protocol/transport GRE/IP


来源: CCNA LAB90: Configuring EIGRP for IPv6
来源: CCNA LAB 91: Configuring Back-to-Back Serial Connections
来源: CCNA LAB92: Verifying Cisco HDLC Encapsulation
来源: CCNA LAB 93: Configuring PPP Encapsulation
来源: CCNA LAB 94: PPP Authentication Using PAP
来源: CCNA LAB 95: PPP Authentication Using CHAP (Method #1)
来源: CCNA LAB 96: PPP Authentication Using CHAP (Method #2)
来源: CCNA LAB 97: Configuring Multilink PPP (MLPPP)
来源: CCNA LAB 98: Configuring PPPoE

来源: CCNA LAB 99: Configuring eBGP Advanced

zmjeffwc 发表于 2023-1-30 09:58:26

{:6_268:}{:6_268:}

thamky 发表于 2023-1-30 10:13:45

{:6_299:}

Joe.Zhangjy 发表于 2023-2-2 01:27:15

{:6_267:}{:6_267:}{:6_267:}

f1662 发表于 2023-2-2 08:32:59

{:6_290:}

leoqt 发表于 2023-2-28 22:50:39

{:6_267:}

lxzhanshe 发表于 2023-3-17 09:24:59

谢谢楼主分享

新野 发表于 2023-3-21 17:06:22

看看,谢谢!!!

lxzhanshe 发表于 2023-3-27 13:14:27

谢谢分享

welinker448 发表于 2025-3-12 23:21:49

{:6_267:}{:6_267:}{:6_267:}{:6_267:}
页: [1]
查看完整版本: CCNA LAB 100: Configuring GRE Point-To-Point Tunnels